Description
PW-CO1440-T2 Drying Baking Wax Melting And Sterilization Large Oven For Laboratory Use
Introduction
Box structure size
2、The controller is located on the top of the machine, the double doors open from right to left；
4、The outer material is SECC steel plate thickness ≥1.2mm powder baking paint treatment；
5、The thermal insulation material is 100K high-density glass rock wool with a thickness of 100mm, which has good thermal insulation and maximizes the temperature insulation.
6、There are two layers inside, two stainless steel grids (mesh shape)；
7、The tight material is high temperature resistant silica gel strip；8、Glassless window;
9、Equipped with movable casters and fixed feet.
Supply unit
Voltage: 380V three-phase Power: 8KW
Parameters and temperature control system
1. The temperature control is PID microcomputer, which can automatically calculate, PV/SV can be displayed at the same time, and it can be set by pressing buttons. Any temperature value between normal temperature and maximum temperature can be set (Taiwan Pine);
2. Timer setting, 99.9 seconds-999 hours (optionally set hours, minutes, seconds,)
a. Continuous use
b. When the temperature is up, the time is up to cut off the heating current (the alarm device ends)
3. CA(K) TYPE temperature sensor head;
4. The output is 3-32V;
5. The current controller is controlled by the solid state relay to control the power output, and the temperature control PID microcomputer contact output, the signal automatically adjusts the output ratio, and can accurately control the temperature overshoot accuracy (Taiwan Yangming);
6. The heating material is stainless steel heater;
7. Temperature range RT～200℃;
8. Heating rate: RT－100℃ for about 15 minutes; 9. Control accuracy: ±1℃;
9. Uniformity of temperature distribution in the box: ±4℃ (no load).
Air supply system
2. The motor is a long-shaft high temperature resistant type with a power of 1hp/50Hz (Taiwan).
3. The 10.5-inch wind wheel is a multi-blade turbine type.
4. Adjustable wind deflector is installed inside.
5. There is an air inlet at the rear and two sets of air outlets on the top, and the exhaust air volume is adjustable.
Safety protection system
1. Over-temperature protection system: When the temperature is out of control due to external forces, the system will automatically stop the power supply of the whole machine when the set temperature exceeds 10 degrees, thereby protecting the safety of your products and machines;
2. Fuse and overcurrent protection system: When the power of the whole machine exceeds the normal power due to high voltage or other reasons, the system will automatically cut off the power to protect the industrial control components of the whole machine from being damaged;
3. Motor overheating protection to prevent motor damage caused by motor overheating, phase sequence protection.
Use Scenarios
Controlled Drying Processes in Quality Control Laboratories
In laboratory environments where precise moisture removal from samples is paramount, this drying baking oven plays a critical role in conditioning materials prior to downstream analysis or manufacturing steps. Operating within stringent temperature tolerances afforded by the PID microcomputer controller, it ensures uniform drying that complies with quality assurance protocols. The forced horizontal air circulation mechanism maintains consistent thermal distribution to prevent hot spots or uneven drying. This oven integrates smoothly with quality control procedures requiring reproducible results and facilitates workflow automation by supporting programmable timer cycles, thereby reducing manual intervention and potential human error.
Sterilization and Sample Preparation in Scientific Research Facilities
Scientific research institutions utilize this industrial drying oven supplier’s product to sterilize laboratory instruments and prepare samples through controlled wax melting or aging protocols at precise temperatures up to 200°C. The robust construction and safety protections permit extended continuous operation essential for lengthy sterilization cycles. The large chamber capacity accommodates bulk processing demands while maintaining compliance with hygienic standards. The oven’s adjustable airflow and temperature uniformity allow researchers to optimize conditions that support reproducible experiment setups and ensure sample integrity. Its compatibility with existing laboratory infrastructure enables streamlined workflows and enhanced operational efficiency.
FAQ
What types of materials can I process in your laboratory oven?
Our laboratory oven is suitable for drying, baking, wax melting, and sterilizing various materials commonly used in industrial and scientific research settings. Its stainless steel chamber and precise temperature control support stable processing of metals, plastics, waxes, and other compounds requiring uniform heat.
Can I request customized temperature ranges or chamber sizes?
We offer customization options on chamber dimensions and temperature controls to meet specific large oven manufacturer requirements. Our engineering team works closely with you to adapt features such as airflow settings and timer functions for your particular industrial drying or baking oven needs.
How is installation and maintenance handled for the drying baking oven?
We provide detailed installation guidelines to ensure proper setup of your industrial drying oven, including electrical connection and positioning. Routine maintenance involves checking safety protections and air circulation components to maintain optimal performance and extend operational lifespan.
Do you provide delivery and after-sales support for your industrial ovens?
Yes, we manage worldwide logistics for our ovens and offer continuous after-sales services. Our expert team supports you from delivery through setup and operation to ensure your laboratory oven factory equipment functions reliably within your production or research environment.
